The tapered barrel on these Split Taper Bushing china bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for make use of with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on a single page as the pulley you need. For employ with 5/8” shaft sizes. Comes with set screws. Additional Features: Manufactured from Steel For apply with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque ability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the need to have a component bored to size, preferably lowering on hand requirements and allowing for adjustments in shaft size if required. The barrel of the split tapered bushing can be split in two places and is certainly keyed to the shaft. The barrel OD can be keyed to the drive component aswell. The advantage of the split tapered bushing is it will hold, whether or not the fasteners turn into loose. Split tapered bushings happen to be interchangeable between manufacturers.
Taper bushing are trusted as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are constructed with high quality engineered products with superb tolerance. The characteristic is easy to apply and needs no additional alteration. These bushings can fit almost a myriad of assemblies and sizes. They are the best choice in design for mechanical connections.
To complete designations put bore size. For example: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: complete selection of both metric and imperial obtainable.
Standard range matches up to 125mm/5″ shafts & Hub diameter required depends upon the application.
Complete short reach range readily available, for compact light in weight assemblies & Clean, Compact Style.
Simple installation and removal.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and will be purchased on the same page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Comes with 2 set screws.
Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for toughness and strength. U1 bushings are being used in an extensively wide selection of applications, which include; sprockets, shaves, pulleys, gears, and much more, we also offer most of these items. What models this bushing apart may be the high-quality steel structure along with exact manufacturing and top quality control; this ensures that you always get a premium quality steady product. What really units us apart from the other fellas 
is our highly trained expert staff members and our company-wide aim of customer satisfaction.
1. Be sure the tapered cone areas of the bushing and the inside of the driven item happen to be clean and free of anti-seize lubricants.
2. Place the bushing in sprocket or various other component type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing continues to be loose to make sure sliding match on shaft.
4. With essential on shaft, slide the sprocket or other part type to the desired job on the shaft. Be sure to leave the heads of the cap screws attainable.
5. Align the sprocket or part type, tighten the screws additionally and progressively until they are pulled up tight. Usually do not employ extensions on the wrench handles and do not allow the sprocket or portion to be drawn i contact with flange of bushing. At this time there should be a gap between your bushing flange and sprocket, make certain this gap will not close.
Twice split barrel ensures concentricity
Grips the shaft with positive clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key of all sizes for confident drive and higher torque carrying capabilities
Double-split barrel for great clamping
Solid flange to keep up concentric bores
Available in inches, metric, and spline bores. Bore range between 3/8″ to 10″
Solid Flange & Twice Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys upon both shaft and item to provide the strongest possible travel.
3/4″ per Foot Taper on Barrel – Personal locking taper provides the highest amount of mechanical locking merchandise to product.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for use with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on the same page as the pulley you need. For employ with 5/8” shaft sizes. Includes set screws. Extra Features: Manufactured from Steel For employ with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, preferably lowering on hand requirements and allowing for changes in shaft size if required. The barrel of the split tapered bushing is usually split in two locations and is certainly keyed to the shaft. The barrel OD is also keyed to the drive component as well. The benefit of the split tapered bushing could it be will hold, regardless if the fasteners become loose. Split tapered bushings will be interchangeable between manufacturers.