All EPT shaft collars, including Shaft Clamp quick-clamping collars, are sole point faced to ensure perpendicularity and proper alignment. This critical manufacturing stage assures precise shaft collar face to bore relationship leading to correct aspect positioning on the shaft and even pressure on interfaced pieces.
Quick-clamping shaft collars from EPT are made of high quality light weight aluminum with type-II sulfuric anodized finishes, with a black finish upon the collar and a precious metal finish upon the clamping lever for added visibility. Light weight aluminum collars are corrosion tolerant, lighter than different metals, have low inertia and also have nonmagnetic properties. All EPT goods happen to be RoHS and REACH compliant. Available typical sizes for the quick-clamping shaft collars are 0.375” to 1 1.5” in the ” series and 8 mm to 38 mm in the metric series.
Shaft Collar, Program of Measurement Inches, Shaft Locking Type – Couplings 1 Piece Quick Clamp, Bore Type – Collars Simple Bore, Bore Dia. 3/8 In., Material – Collars Black Anodized 6061 Aluminum, External Dia. 1-1/2 In., Width .394 In., Clearance Dia. 1.496 In., Screw Size M3, Screw Material 18-8 300 Series STAINLESS, Operating Temp. Selection -40 Degrees to 200 Degrees F, Expectations RoHS2 Compliant, REACH Compliant
The Shaft Collar 1×3/8, 1/2″ for Key Shaft is made of lightweight Aluminum, the two piece design allows you to install these collars anywhere on a shaft without removing components. Furthermore to reducing the entire weight, the flats permit you to rotate a shaft without marring or gouging the shaft. Basically place the collar on the shaft and tighten both socket-mind cap screws to safeguarded the collar and a wrench and become added to the collar’s flats to rotate the whole shaft/collar assembly.
Made of lightweight Aluminum
Permits you to install these collars anywhere on a shaft without removing components
Basically place the collar about the shaft and tighten the two socket-head cap screws to secure the collar
Flats let you rotate a shaft without marring
Climax Part C-056-S Collection Screw Collar is made with T303 Stainless Steel, which works well in corrosive environments. Sizes happen to be 9/16 in. Bore, 1 in. OD, 7/16 in. Width. It really is successful on hard and very soft shafts. This is a Affordable collar design, and Conveniently installed where significant disassembly would normally be required.
EPT speedy clamping shaft collars collar clamp hinge buy manufacturing 2 1 8 in steel,shaft collar clamp induce manufacturing steel vex clamping style,vex clamping shaft collar collars 1 part with lever clamp hinge,vex clamping shaft collar clamp 3d model making quick 1 3 8 in alum,EPT speedy clamping shaft collars collar clamp 2pc 1 in metal stainless split with lever,climax metallic s shaft collar two part clamp style EPT speedy clamping collars 2pc 1 in steel induce,clamp on shaft collars couplings universal clamping collar design with mounting holes 2pc 1 in steel,shaft collar clamp push clamping calculation quick hook up collars at best value in,clamp shaft collar clamping collars force calculation quick connect,stainless steel dual split shaft collar with speedy clamping clamp hinge push calculation.
Black Oxide Plated Steel One-Piece Clamping Collar.
Recessed Screw Head provides an outside surface free from major projections for safety.
Design completely engages the shaft without marring.
Greater axial holding electricity than established screw collars.
Effective on hard & delicate shafts.
Indefinitely adjustable and simple to remove, one-piece clamping collars are usually applied to hard or delicate standard round shafts, above a split hub or about thin wall tube. Through the use of friction to provide superior grip on pubs and shafts, one split collars deliver sturdier, more trustworthy results in comparison with the set screw style of solid collars. They also offer tremendous axial ability, while minimizing shaft distortion for superior performance and decreased wear and tear.
The collar clamping mechanism works quickly and proficiently with simple side opening of the integral clamping lever, positioning the collar on the shaft, and closing the lever flush with the outer area of the collar. The design of the cam on the lever and the mating machined area on the collar assure a tight fit with a optimum axial load of 35 to 120 lbs / 133 to 489 N based on the collar bore size. In circumstances where higher holding power is normally or clamp axial load is required, the quick-clamping collar is not the recommended decision. EPT offers a total line of industry-leading one-piece and two-piece shaft collars suitable for these applications.