The initial sheave and pulley mounting program developed to facilitate installation and replacement of components.
The QD (Quick Detachable) design offers both conventional (flange outboard) and reverse (flange inboard) installation configurations.
1. Be sure the tapered cone surfaces of the qd bushing china bushing and the inside of the driven item are clean and free of anti-seize lubricants.
2. Slide QD bushing on shaft, flange end first. Assemble key.
3. Placement QD bushing on shaft. Tighten set screw over key “hand tight” with standard Allen wrench only. Do not use excessive force.
4. Slide huge end of sheave or sprocket taper bore into placement over cone aligning drilled bolt holes in sheave or sprocket with tapped holes in flange of bushing. Assemble pull-up bolts and lock washers.
NOTE: Install M thru S bushings in the hub so that both extra holes in the hub are located as far as feasible from the bushing’s saw cut.
5. Tighten pull-up bolts alternately and evenly to tightness indicated in torque desk on back. Do not use extensions on wrench handles. There should be a gap between the encounter of the sheave or sprocket hub and the flange of the QD bushing to insure a satisfactory cone grip and press fit.
CAUTION: THIS GAP SHOULD NOT BE CLOSED.
Use a tapered or QD bushing from Ever-Power with sheaves, pulleys, sprockets and several other power tranny applications. Flanged quick-disconnect bushings include a completely split style to help provide easy installation and disassembly. A tapered bushing with directly edges uses an interior screw to greatly help drive the bushing into the shaft, while a split taper includes a flange and a key on the bushing to greatly help provide more drive.
QD bushings (inch and metric sizes) have a flanged style and show a 4° taper with typical or reverse mounting. They are stocked in popular finished bore sizes and minimum plain bore for custom reboring.
Many people refer to both types as a “taper lock” because they both utilize the tapered wedging action to lock to the shaft. The taper bushing, with it’s straight sides, uses a set screw to operate a vehicle the bushing into the bore of the component getting installed (sheave, sprocket, etc.). Be careful when installing these screws. The holes with threads on the bushing are for removal only. Also remember that the appearance of a flange externally of the bushing doesn’t necessarily mean it’s a QD style. Split Taper bushing also has a flange, and both are not interchangeable. The QD style has a split that proceeds through the flange. The Steel QD (Quick Disconnect) Type bushing offers flexible and easy installation while providing exceptional keeping power. QD Bushings are used considered the industry offering convenience and design flexibility. They are precision machined of quality Metal and are installed by tightening several cap screws. This draws the bushing into the taper bore of the merchandise which compresses the bore of the bushing. QD bushings are easily removed by using the cap screws as jack-screws. Double drilled holes are furnished in QD Bushings permitting installation of product in the traditional or invert positions. This allows cap screws to end up being installed through item hub or bushing flange whichever is certainly most convenient. A significant benefit in installation, cap screws are constantly inserted from the exterior where they are often accessible. QD Bushings are available from stock with all popular bores within the number of each size bushing.
QD Bushings feature a split tapered flange with the split central to the flange and taper. They are applied to sprockets, sheaves, and pulleys where more clamping force is required over standard bored-to-size bushings. Quick-Disconnect Bushings are crucial for mounting v-belt drives, synchronous belt drives and roller chain drives.
Our immediate supply chain to Martin Sprockets factories gets a wider range of QD Bushings delivered at the right time at the proper price.
Taper bushing are widely used as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are made from high quality engineered components with great tolerance. The feature is certainly easy to use and needs no extra alteration. These bushings can suit almost all types of assemblies and sizes. They will be the best choice in design for mechanical connections.
No costly re-boring: full selection of both metric and imperial available.
Standard range matches up to 125mm/5″ shafts & Hub diameter required depends on the application.
Complete brief reach range obtainable, for compact lightweight assemblies & Clean, Compact Design.
Simple installation and removal.
The original sheave and pulley mounting system developed to facilitate installation and replacement of components.
The QD (Quick Detachable) design offers both conventional (flange outboard) and invert (flange inboard) installation configurations.
1. Be certain the tapered cone surfaces of the bushing and the inside of the driven item are clean and free from anti-seize lubricants.
2. Slide QD bushing on shaft, flange end first. Assemble key.
3. Placement QD bushing on shaft. Tighten arranged screw over key “hands tight” with regular Allen wrench only. Usually do not use excessive force.
4. Slide huge end of sheave or sprocket taper bore into position over cone aligning drilled bolt holes in sheave or sprocket with tapped holes in flange of bushing. Assemble pull-up bolts and lock washers.
Notice: Install M thru S bushings in the hub so that the two extra holes in the hub can be found as far as feasible from the bushing’s saw cut.
5. Tighten pull-up bolts alternately and evenly to tightness indicated in torque desk on back. Usually do not use extensions on wrench handles. There should be a gap between your encounter of the sheave or sprocket hub and the flange of the QD bushing to insure a satisfactory cone hold and press fit.
CAUTION: THIS GAP MUST NOT BE CLOSED.
Use a tapered or QD bushing from Ever-Power with sheaves, pulleys, sprockets and many other power transmitting applications. Flanged quick-disconnect bushings feature a completely split style to help provide easy set up and disassembly. A tapered bushing with straight edges uses an interior screw to greatly help drive the bushing in to the shaft, while a split taper has a flange and an integral on the bushing to help provide more drive.
QD bushings (” and metric sizes) have a flanged design and feature a 4° taper with standard or reverse installation. They are stocked in popular finished bore sizes and minimum plain bore for custom reboring.
Many people make reference to both types as a “taper lock” because they both utilize the tapered wedging action to lock to the shaft. The taper bushing, with it’s straight sides, uses a set screw to drive the bushing into the bore of the component being set up (sheave, sprocket, etc.). Be cautious when installing these screws. The holes with threads on the bushing are for removal only. Also remember that the looks of a flange externally of the bushing doesn’t necessarily mean it’s a QD design. Split Taper bushing also offers a flange, and the two are not interchangeable. The QD design includes a split that continues through the flange. The Metal QD (Quick Disconnect) Type bushing offers flexible and easy set up while providing exceptional holding power. QD Bushings are utilized thought out the industry offering convenience and design flexibility. They are precision machined of quality Metal and are installed by tightening several cap screws. This draws the bushing in to the taper bore of the product which compresses the bore of the bushing. QD bushings are easily removed by using the cap screws as jack-screws. Double drilled holes are furnished in QD Bushings permitting installation of product in the traditional or reverse positions. This allows cap screws to end up being installed through product hub or bushing flange whichever can be most convenient. A significant benefit in set up, 
cap screws are always inserted from the outside where they are easily accessible. QD Bushings are available from share with all popular bores within the range of every size bushing.
QD Bushings feature a split tapered flange with the split central to the flange and taper. They are applied to sprockets, sheaves, and pulleys where more clamping power is necessary over standard bored-to-size bushings. Quick-Disconnect Bushings are crucial for mounting v-belt drives, synchronous belt drives and roller chain drives.