helical bevel gear reducer

The EP Series Helical Bevel Reducer provides unmatched performance, durability, and design flexibility. This unit provides torque capacities up to 20,000 Nm (14,750 ft pounds).
The cat4CAD software allows simple interactive product selection of the entire gearbox and gear-engine system. Cat4CAD supports you in selecting and configuring the products, provides you the opportunity to print out considerable technical data sheets, and generates complete 2D drawings and 3D versions for direct download.
11 sizes
Insight power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Course 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and better torques in smaller sizes.
Multiple Input Options: Essential gear motors, ” or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Options: Hollow bores and shrink disks for shaft installation, inch and metric result shafts, installation pilots and flanges provide an array of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal mounting on five sides or with a torque arm.
Worldwide Motor: Multiple leads and windings for worldwide multi volt/Hz requirements in addition modular design to simply accept brakes, encoders or pressured cooling.
High efficiency electric motor design available
Innovative self-locking, self-aligning taper shaft engine connection
Gearbox supplied factory filled up with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals upon heat treated, plunge surface shafts
Shaft mounting options include tapered bushings designs
This is a comprehensive offering of energy-efficient, right angle helical bevel enclosed gearing. It really is available as gearmotors and a variety of reducers with torque capacities up to 119,000 inch pounds. Housing styles include footed, face and flanged configurations. Gearmotors can be found in three phase high efficiency styles through 50 HP and single phase to 5 HP. We provide a selection of input and result shaft choices. Additionally, you will see fixed and variable quickness motors and range of ratios obtainable in this product offering.
Features
Accommodates input power from ¼ Hp to 75Hp
Torque ratings up to 119,489 in-lbs
Reduction ratios up to 7,500:1
Helical – bevel – helical gear train offers cost effective high and low speed solutions
Up to 94% efficient
Four input possibilities for all units
Two output flange choices – B5 and B14
Multiple output shaft interfaces
Crucial dimensions interchangeable with major competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
Heavy Duty Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the developing and varying needs of customers, we offer a wide variety of Helical Bevel Equipment Reducers. The technological content of our products allows for an extraordinary efficiency/lifespan ratio. The highly versatile Helical Bevel Gear Reducers we provide are successfully found in a multitude of commercial and civil applications. These are B-Series units that offer excellent affordability and result torque/weight ratio, especially considering that they need not a lot of servicing. Besides these, our products can be found in cast iron (sizes 063 to 163) or light weight aluminum (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for electric motor coupling, IB with input shaft, CB with compact motor, PB-fitted for electric motor coupling with flexible joint
Casing with feet FC, flange SC and general UC
Power up to 90 kW
Gears hardened and tempered with shaved or ground profile
Gearing with 3 reduction stages
Gleason spiral bevel equipment pairs with run-in profile, mounted as second reduction stage for a higher resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-power casings optimized with FEM analysis and input and output flanges of grey cast-iron G200 to ensure top level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, result flange, result shaft, shrink disk, backstop device, protection cover kit, viton oil seals, reinforced result, assemble/disassemble kit
Series EP right position helical bevel equipment motors provide ratios from 8:1 to 160:1 in three levels or up to 10000:1 in five levels. Motors are available up to 90kW and output torque capacity up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and will be offered with single or double extended output shafts.
Units are also available because shaft mounted or with output flanges and are available for installation horizontally or vertically. The devices can also be provided with a bolt on torque response bracket and all variants are available possibly motorised or with an insight shaft assembly.
Adding to the brand new selection of Ever-Power helical equipment motors this product takes benefit of our many years of accumulated design experience together with the use of top quality materials and parts. The end result is a series of velocity reducing geared motors offering high load transporting capacities, increased efficiency, quiet running and reliability.
Top features of Helical Bevel Gear Motor
Standard motor connection
Ability to fit double essential oil seals, on insight and output shaft since required.
All units are dimensionally interchangeable with other major manufacturers.
Units are manufactured and assembled from a family of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units could be installed with a backstop module and reducer Products can be fitted with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are used in industries such as chemicals, pharma, packaging, food processing, plastic-type and automation etc.
Key Features:
Sizes: A40-A50-A70
Available versions: EP – fitted for motor coupling, IEP – with input shaft, CEP – with compact motor
Cases with foot, flange or universal
Power up to 4,8 Kw
Gears with shaved or floor profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in helical bevel gear reducer die-cast aluminium alloy
Excellent mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in in accordance to DIN 1843
Accessories: torque arm, output flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission gadget and made up of Y series motor, helical gear,Arc gear and worm gear. The gears are constructed with high wear-resisting alloy materials, specially and finely processed.
Advantages:
1: Helical-bevel gear two-stage reducer
2: Compact framework, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Compact design, small volume, good appearance ,and strong capacity to be overloaded.
6: Precise division and wide selection for transmission ratio.
7: The performance is up to because high since 96% with low energy usage, strong adaptability and is with the capacity of functioning continually in corrosive or damp environment.
8: All- purpose use, convenient and low-cost maintenance.
9: New seal gadget, strong adaptability.
10: Varied selection of motor combinations, mouting positions and struture projects.