EP brand name replacement gearbox for woods rotary gearbox
NEW forty HP GEARBOX Clean Enter one three/8 12 spline output Interchangable with marketplace popular measurement i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Numerous A lot more
Functions
(one) model new 45 horse electrical power shearpin gearbox. This gearbox fits many diverse helps make of 4′,5′ and some 6′ rotary cutters. I offer a whole lot of these bins every single year for numerous distinct programs and carry ALL Alternative Parts for this box, but ideally you will not likely have to be concerned about that.
Listed here are the specs on the box:
*45 horse energy gearbox
*Common one-three/eight” sleek enter shaft(exactly where the pto shaft hooks on). The pto shaft is held on by a one/2 shearbolt.
*length of the input shaft out of the gearbox is 3″ extended
*bolt gap pattern for mounting is on the corners, 4-3/four heart of hole to middle of gap. It takes a five/8″ bolt.
*12 splined output shaft(the place the blade provider hooks up on the base)
*one-9/sixteen exterior measurement in excess of the output shaft splines- from the base of the output cap to the stop of the splines is two-three/four” long- total size of the output shaft is four-1/2″ prolonged.
*normally takes a 1″ threaded castle nut and a carter essential on the base of the output shaft to secure blade pan(NUT is integrated – – BLADE PAN IS NOT!!)
*total height of the box from the prime of the mower deck to the best of the box is 9-1/2″
This is a fairly large product (forty seven lbs.) so freight is not low cost, but we do not make something off of freight, whatsoever ups charges us we demand you.
40 HP
1:one:47 Ratio
one-3/8″ Clean Enter Shaft with Shear Pin Hole
one-1/2″ twelve-Spline Ouput Shaft
Bolt Sample: 6-1/2″ (4) five/eight” Holes, five” Center Hole Required for Shaft Assembly
The Input and Output Shafts Can’t be Acquired Serparately.
They are Bought as a kit.
The package involves the pursuing parts: input shaft, input gear, output shaft, output equipment.
The Shaft Package Are not able to Be Divided.
EP brand replacement gearbox for woods rotary gearbox
Rotary Cutter Gearbox Troubleshooting Guidebook
Is your mower leaking, creaking or otherwise performing improperly? You have come to the correct area.
Read through beneath for the most frequent troubles with rotary cutter gearboxes and their options (from rapid and dirty, to specialist).
Leaking Bottom Seal:
If you have wrapped some baling or fencing wire around your output shaft and blown the seal, the expert thing to do is to substitute the seal.
If your output seal is intact, and you are able to get ID, OD and thickness measurements (in millimeters), most bearing properties can purchase you up a generic double-lip seal that will get you back again up-and-working. If not, give us a get in touch with and we can support you sort out what you require.
A 
dental select is the best way to take away the previous seal before urgent in the new one particular.
If you are fortunate ample to have a slow-leak, the swift and soiled technique is to run automotive-kind grease in the gearbox till the new seal comes in. Be certain to verify and incorporate grease more frequently than you would with oil, as this is NOT a skilled restore.
Broken Output Shaft:
Uh oh. You hit one thing that didn’t shift. The very good news is that the output shaft on most gearboxes is pretty straightforward to change. The poor information is… it really is seldom an isolated failure.
The initial thing to do is to take aside your gearbox and evaluate the full extent of the injury. If it is truly just the output shaft, you must be able to alter it out, no difficulty. The output shafts begin at about $70 and go up in cost based on the measurement of the gearbox.
Nonetheless, in most situations, the bearings ($twenty/ea), seals ($ten/ea) and gear-established ($70) will also usually consider a beating. If you are unfortunate, the output cap ($eighty) will also suffer some injury.
In this case, it is normally cheaper to substitute the gearbox. Assess the price of components to the cost of an total, new, warrantied gearbox. At times, even specialists have to know when to get in touch with it a working day.
I Want to Alter my Input Shaft:
If you are exhausted of changing shear pins or seeking back and observing that your mower has not been slicing, you could want to install a slip-clutch pto shaft (Indeed, we sell people way too).
This typically calls for setting up a 540-design, six-spline input shaft ($eighty five) on your mower’s gearbox.
Blessed for you, we did a create-up on our blog. It really is called “How to alter the enter shaft on your rotary cutter gearbox”.
My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all sound sort-of comparable more than-the-mobile phone. The greatest point to do is to disassemble your gearbox and get a seem at the gears and bearings. The situation will generally existing itself in the way of broken/missing gear tooth, toasted gears (like that image on our home web page), or blown bearings.
If every thing seems typical, try modifying the equipment-mesh. This is done with the mylar “gaskets” that sit among the primary gearbox case and the enter/output caps. Consider introducing or taking away some of these spacers until your gears have about one/eight”-1/four” of free of charge enjoy. Pros can order replacements ($one-2) in various thicknesses, but we suggest the quick and filthy strategy of reducing your possess out of a sheet of mylar.
Will not forget to re-seal the gearbox with RTV following you’ve got found the proper blend. Even though they’re known as “gaskets”, they won’t seal your gearbox on their very own.
Our Gearbox For Fertiliser Spreaders is the best and also most ingenious in the market.